Nasrul Amri Mohd Amin, Assoc. Prof. Ir. Ts. Dr.
Browse by
About Associate Professor Ir. Ts. Dr. Nasrul Amri Bin Mohd Amin
Associate Professor Ir. Ts. Dr. Nasrul Amri Mohd Amin is currently a Associate Professor at Faculty of Mechanical Engineering Technology, Universiti Malaysia Perlis
He was formerly from School of Manufacturing Engineering
ORCID ID: https://orcid.org/
Scopus Author ID: 54789468600
Email: Nasrul Amri Mohd Amin
Research Interests
Mechanical Properties
Numerical Modeling
Renewable Energy
News
Skills and Expertise: Materials, Mechanical Properties, Fluid Mechanics, Computational Fluid Dynamics, Renewable Energy Technologies, Numerical Simulation, Numerical Modeling, CFD Simulation, Engineering Thermodynamics, Aerodynamics, Thermal Engineering, Mechanical Engineering, Energy, Energy Engineering, Composites, Renewable Energy, Heat Exchangers, Experimental Fluid Mechanics, Heat Transfer, Applied Thermodynamics, Convection, Thermal Analysis, Energy Storage, Thermal,Conductivity, Fluid, UAV, Refrigeration & Air Conditioning, CFX, Heat Capacity, Petroleum Engineering, Nuclear Engineering, Pcm and Aircraft Design.
Recent Submissions
-
The Characterization of Bario Rice Starch-nanoHA Scaffolds using SEM and Dielectric Measurement
(IOP Publishing, 2019)Bone tissue scaffold had been ventured for over the decades as a solution for bone failure and trauma. Starch is the most common natural polymer that has been used as a biomaterials and a good candidate for scaffold ... -
The Optimization of the Hydroxyapatite (HA) Material Characteristics Produced from Corbiculacea (Etok) Shells
(IOP Publishing, 2019)Hydroxyapatite commonly used in medical field for tissue disease, bone disease, drug delivery and also for non-medical field purpose such as wastewater treatment. Due to excellent biocompatibility and bioactive properties, ... -
Optimisation of a phase change thermal storage system
(World Academy of Science, Engineering and Technology (WASET), 2009-10)PCMs have always been viewed as a suitable candidate for off peak thermal storage, particularly for refrigeration systems, due to the high latent energy densities of these materials. However, due to the need to have them ... -
Maximizing the energy storage performance of phase change thermal storage systems
(ACTA Press, 2009-03)Phase Change Material (PCM) is considered as a good Thermal Energy Storage (TES) material as it can provide much higher energy storage densities compared to conventional sensible thermal storage materials. An extensive ... -
Effective thermal conductivity for melting in PCM encapsulated in a sphere
(Elsevier Ltd., 2014-06)Heat transfer in phase change materials (PCMs) contained in spherical encapsulations can be modelled more simply if an effective thermal conductivity can be determined to represent the natural convection occurring within ... -
The interlaminar shear strength test of helical wound glass fibre reinforced epoxy laminates subjected to hydrothermal ageing
(Trans Tech Publications, 2014-06)This paper presents the experimental investigation of interlaminar shear strength (ILSS) tests of helical wound glass fibre reinforced epoxy (GRE) pipes subjected to hydrothermal ageing. Currently, the test is being used ... -
Strength of three-point-bending ductile adhesive joint with dissimilar adherent
(Trans Tech Publications, 2014-06)In this study, an experimental investigation was conducted in order to determine the effect of different adhesive thickness (i.e., 0.1, 0.5, 0.7 and 1 mm) on strength of ductile adhesive joint. The study scope covers both ... -
Stress and thermal analysis of CubeSat structure
(Trans Tech Publications, 2014-06)This paper presents the stress and thermal analysis on the CubeSat structure to study the survivability of the CubeSat during the launching process or operating condition at the orbit is presented. Various design of ... -
Effects of elevated temperatures on the compression strength of nanoclay filled unsaturated polyester resin
(Trans Tech Publications, 2014-06)The paper describes the effects of the montmorillonite (MMT) fillers commonly known as nanoclay, on the compression properties of unsaturated polyester resins at different weight percentage of nanoclay. Modified resin ... -
3D finite element stress analysis of butt adhesively bonded dissimilar joint: effect of bond thickness on strength
(Trans Tech Publications, 2014-06)The butt joint is the most studied type of adhesive joints in the literature. However, the joint strength prediction of joints is still a controversial issue as it involves a lot of factors that are difficult to quantify ... -
Tensile strength of untreated napier grass fibre reinforced unsaturated polyester composites
(Trans Tech Publications, 2014-06)This paper describes the experimental investigation of the tensile strength of untreated Napier grass fibre reinforced polyester composites. Napier grass fibres were extracted trough conventional water retting process and ... -
Modelling of multi-axial ultimate elastic wall stress (UEWS) test for glass fibre reinforced epoxy (GRE) composite pipes
(Trans Tech Publications, 2013)This paper describes the modeling of multiaxial ultimate elastic wall stress (UEWS) at room temperature for glass fibre reinforced epoxy (GRE) composite pipes. The model developed, predicts the stress-strain response caused ... -
General lifetime damage model for glass fibre reinforced epoxy (GRE) composite pipes under multiaxial loading
(Trans Tech Publications, 2014)This paper presents the modelling of a general lifetime performance for glass fibre reinforced epoxy (GRE) composite pipes similar to the well-known Tsai-Hill interactive failure criterion. Tsai Hill criterion is based on ... -
General lifetime damage model for glass fibre reinforced epoxy (GRE) composite pipes under multiaxial loading
(Trans Tech Publications, 2014)This paper presents the modelling of a general lifetime performance for glass fibre reinforced epoxy (GRE) composite pipes similar to the well-known Tsai-Hill interactive failure criterion. Tsai Hill criterion is based ... -
Experimental studies of a Ranque-Hilsch vortex tube
(Trans Tech Publications, 2013)Vortex tube is a device that separates a compressed flow of gas into two streams simultaneously, one giving kinetic energy to the other, resulting one hotter than the inlet temperature and one lower, without having any ... -
Experimental investigation of PCM spheres in thermal energy storage system
(Trans Tech Publications, 2013)This paper presents the experimental result of a small scale packed bed of random spheres with encapsulated PCM being charged and discharged. A vapor compression refrigerator and heated room with fan heater were used to ... -
Effectiveness–NTU correlation for low temperature PCM encapsulated in spheres
(Elsevier Ltd., 2012-05)The applicability of the effectiveness–NTU method for characterising a PCM thermal energy storage system was experimentally investigated. The system consisted of PCM encapsulated in spheres with a liquid heat transfer ... -
Optimising PCM thermal storage systems for maximum energy storage effectiveness
(Elsevier Ltd., 2012-09)A new performance parameter for PCM thermal storage systems, the energy storage effectiveness, is defined. This parameter can be used to optimise the design of any PCM thermal storage system to maximise the use of the ... -
Investigation of conducting pins in sphere filled with phase change material for enhancing heat transfer in thermal energy storage
(Trans Tech Publications., 2012)The utilisation of phase change material (PCM) for thermal energy storage (TES) can significantly enhance the energy savings achievable with renewable thermal systems. Sphere based packed bed systems have been used as TES ...