Murizam Darus, Mr.

 

About Mr. Murizam Bin Darus

Mr. Murizam Darus is currently Lecturer at Faculty of Mechanical Engineering Technology, Universiti Malaysia Perlis

He was formerly from Centre of Excellence for Geopolymer and Green Technology

ORCID ID: https://orcid.org/0000-0001-9416-0184

Scopus Author ID: 55560769800

Email: Murizam Darus


Research Interests


Recent Submissions

  • Alteration of solution treatment condition to the precipitation behaviour A319 alloy 

    Murizam, Darus; Shamsul, Baharin Jamaludin, Prof. Dr.; Mohd Arif Anuar, Mohd Salleh; Faizul, Che Pa; Ruhiyuddin, Mohd Zaki (Trans Tech Publications, 2013)
    The development of precipitate during ageing treatment of A319 alloy contributed significantly to the alloy strengthening mechanism. Two solution treatment temperatures which were set at 510°C and 525°C were subjected onto ...

  • Effect of pyrolysis temperature on the synthesis of carbon fiber from natural organic waste 

    Shahrizam, Saad; Faizul, Che Pa; Mohd Mustafa Al-Bakri, Abdullah; Ruhiyuddin, Mohd Zaki; Murizam, Darus (Trans Tech Publications, 2014)
    Carbon fibers are produced from natural sources of water hyacinth plants that have been dried, ground and sieved to three different particle sizes of 600 μm, 300 μm and less than 300 μm. Through the analysis of data obtained ...

  • Synthesis and characterization of iron produced from iron mill scale 

    Ruhiyuddin, Mohd Zaki; Murizam, Darus; Khairel Rafezi, Ahmad, Dr. (Trans Tech Publications, 2014-01)
    In this project, iron mill scale has been used to produce iron powder that can be used within the Powder Metallurgy process. To achieve this objective, the iron mill scale needs to be refined. This involve the work of ...

  • Potential application of palm ash as a raw materials in production of green glass 

    Noorina Hidayu, Jamil; Mohd Mustafa Al Bakri, Abdullah; Faizul, Che Pa; Ruhiyuddin, Mohd Zaki; Murizam, Darus; Che Mohd Ruzaidi, Ghazali, Prof. Madya; Mohamed Faisol, Mohamed Nor (Scientific.Net/Trans Tech Publications, 2012-12)
    Oil Palm Ash is one of the abundance agricultural wastes found in Malaysia. This wastes need to be disposed properly. Oil palm ash contains compounds needed to produce glass. Most of raw materials (especially silica) used ...

  • Potential application of palm ash as raw materials to produced green glass 

    Faizul, Che Pa; Noorina Hidayu, Jamil; Ruhiyuddin, Mohd Zaki; Murizam, Darus; S. Shahrizam; Che Mohd Ruzaidi, Ghazali, Prof. Madya; Mohamed Faisol, Mohamed Nor (Universiti Malaysia Perlis (UniMAP), 2012-06-18)
    Oil Palm Ash is one of the abundance agricultural wastes found in Malaysia. This wastes need to be disposed properly. Oil palm ash contains compounds needed to produce glass. Most of raw materials (especially silica) used ...

  • Study on milling periods on the iron mill scale particle size and properties 

    Ruhiyuddin, Mohd Zaki; Faizul, Che Pa; Murizam, Darus; A. R. M., Nazri (Trans Tech Publications, 2013)
    The relations between the milling periods with the iron mill scale particle size have been studied. Iron mill scale has been chosen for this research due to the nature of itself, as a by-product. From this research, the ...

  • Recycled Aluminium Composite Pulley 

    Mazlee, Mohd. Noor; Shamsul Baharin, Jamaludin, Prof. Dr.; Murizam, Darus (Malaysian Invention & Design Society (MINDS), 2006-05-19)
    Recycle Aluminium Composite Pulley was an environmental-friendly pulley from innovative recycle aluminium composite materials. This pulley was fabricated by using recycled aluminium alloy from automotive component reinforced ...

  • Determination of crystal changes on sodium cobaltite (NaCo 2O4) by Reitveld analysis as a suitability function in thermoelectric materials 

    Muhammad Asri, Idris; Murizam, Darus; Norsuria, Mahmed (American Institute of Physics, 2010-03-11)
    Sodium Cobaltite, NaCo2O4 has been studied extensively as a new thermoelectric material. The cobalt oxide position in each sodium unit cell may determine the power produced by this type of thermoelectric materials. In this ...

  • Recycled Aluminium Composite Pulley 

    Mazlee, Mohd. Noor; Shamsul Baharin, Jamaludin, Prof. Dr.; Murizam, Darus (International Exhibition of Inventions, 2007-04-18)
    Recycle Aluminium Composite Pulley was an environmental-friendly pulley from innovative recycle aluminium composite materials. This pulley was fabricated by using recycled aluminium alloy from automotive component reinforced ...

  • Analysis of binary Aluminium-Magnesium products with varying compositions and optimum flowbility, tensile strength and hardness 

    Mohd Ichwan Nasution, Ir.; Murizam, Darus; Noor Mariamadzliza, Mohd Nan; Noor Azira, Mohd Noor; Kamrosni, Abdul Razak (Universiti Malaysia PerlisSchool of Materials Engineering, 2008)
    This reasearch is to investigate how far the influence on mechanical properties and microstructure of varying aluminium-magnesium alloy using CO2 moulding process. Casting is a process that can produce a complex and ...

  • Role of clay (Bentonite) on mold making process in foundry metallurgy 

    Mohd Ichwan, Nasution; Mohd Nasir, Zainal Arif; Che Mohd Ruzaidi, Ghazali; Khairel Rafezi, Ahmad; Faizul, Che Pa; Mohd Fitri, Mohamad Wahid; Murizam, Darus (Universiti Kebangsaan Malaysia (UKM), 2008-12-03)
    The foundry engineer is usually familiar with the fact that there are different types of clay,such as kaolinite and montmorillonite (bentonite). The bonding action of kaolinite in moulding sands results from the free ionic ...

  • The application of Fluidity Spiral in sand-mold casting 

    Mohd Ichwan, Nasution; Mohd Nasir, Zainal Arif; Che Mohd Ruzaidi, Ghazali; Shamsul Baharin, Jamaludin; Khairel Rafezi, Ahmad; Faizul, Che Pa; Mohd Fitri, Mohamad Wahid; Murizam, Darus (Universiti Kebangsaan Malaysia (UKM), 2008-12-03)
    The term fluidity is always used in the cast-metals industry. Fluidity is the reciprocal of viscosity. The foundryman job is to search the amount of quantity that will permit him to evaluate the relative ability of a given ...

  • Study of Spot Welding of Austenitic Stainless Steel Type 304 

    Shamsul Baharin Jamaludin, Assoc. Prof. Dr.; M.M. Hisyam; Shaiful Rizam Shamsudin; Murizam Darus; Mohd Fitri Mohamad Wahid (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    In this study, austenitic stainless steel type 304 were welded by resistance spot welding. The relationship of nugget diameter and welding current was investigated. Hardness distribution along welding zone was also ...

  • New Approach to Aluminium-Polymer Alloys 

    Mohd Ichwan, Nasution; Mohd Nasir, Zainal Arif, Prof.; Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Shamsul Baharin, Jamaludin, Assoc. Prof. Dr.; Faizul, Che Pa; Murizam, Darus; Che Idrus, Omar; Lee Liu Mei (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    New approach to aluminium-polymer alloys prepared by in-situ mixing or addition of molten metal onto polymer granules will be highlighted. This concept is simple and never been attempted before due to the thermal instability ...

  • Acrylic Pattern for Sand Mould 

    Mohd Ichwan, Nasution, Ir.; Shamsul Baharin, Jamaludin, Assoc. Prof. Dr.; Faizul, Che Pa; Murizam, Darus (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    Patterns used in casting process may be made of wood, metal, plastics or other materials. Pattern are fabricated to obtain good standards of product, so that they can last for a period of time, depending to the quality ...

  • Effect of Solution Treatment Temperature on Recycled Aluminium Alloy 319 

    Murizam Darus; Shamsul Baharin Jamaludin, Assoc. Prof. Dr. (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    In the present work, the responses of artificial ageing process to different solutionising temperatures on recycled 319 series aluminium alloy are studied. The optimisation of solutionising temperature may lead to the ...