• Optimisation of Shrinkage and Strength on Thick Plate Part Using Recycled LDPE Materials 

  Norshahira, Roslan; Shayfull Zamree, Abd Rahim; Abdellah El-hadj, Abdellah; Mohd Mustafa Al Bakri, Abdullah; Błoch, Katarzyna; Pietrusiewicz, Paweł; Nabiałek, Marcin; Szmidla, Janusz; Kwiatkowski, Dariusz; Correia Vasco, Joel Oliveira; Mohd Nasir, Mat Saad; Mohd Fathullah, Ghazali (MDPI AG, 2021-04-05)

  Achieving good quality of products from plastic injection moulding processes is very challenging, since the process comprises many affecting parameters. Common defects such as warpage are hard to avoid, and the defective ...

• Tool wear and surface evaluation in drilling fly ash geopolymer using HSS, HSS-Co, and HSS-TiN cutting tools 

  Mohd Fathullah, Ghazali; Mohd Mustafa Al Bakri, Abdullah; Shayfull Zamree, Abd Rahim; Gondro, Joanna; Pietrusiewicz, Paweł; Garus, Sebastian; Stachowiak, Tomasz; Victor Sandu, Andrei; Muhammad Faheem, Mohd Tahir; Erdi Korkmaz, Mehmet; Mohamed Syazwan, Osman (MDPI AG, 2021-03-26)

  This paper reports on the potential use of geopolymer in the drilling process, with respect to tool wear and surface roughness. The objectives of this research are to analyze the tool life of three different economy-grade ...

• Warpage optimisation using Recycled Polycar-bonates (PC) on Front Panel Housing 

  Nur Aisyah Miza, Ahmad Tamizi; Abdellah El-hadj, Abdellah; Mohd Mustafa Al Bakri, Abdullah; Nabiałek, Marcin; J. Wysłocki, Jerzy; Jeż, Bartłomiej; Palutkiewicz, Paweł; Rozyanty, Abdul Rahman; Mohd Nasir, Mat Saad; Mohd Fathullah, Ghazli (MDPI AG, 2021-03-15)

  Many studies have been done using recycled waste materials to minimise environmental problems. It is a great opportunity to explore mechanical recycling and the use of recycled and virgin blend as a material to produce new ...

• Analysis of Strength on Thick Plate Part using Genetic Algorithm Optimisation Method 

  S., M. Azlan; Shayful Zamree, Abd Rahim; Mohd Nasir, Mat Saad; Mohd Sazli, Saad; M., M. Rashidi; Mohd Fathullah, Ghazli @ Ghazali (EDP Sciences, 2016)

  This study focuses on the optimisation of the injection moulding parameters to maximise the strength ofmoulded parts using a simulation software. The moulded parts were injected with Acrylonitrile- Butadiene-Styrene (ABS) ...

• Shrinkage analysis on thick plate part using Response Surface Methodology (RSM) 

  M. Isafiq; Shayful Zamree, Abd Rahim; ‪Mohd Nasir, Mat Saad; M., M. Rashidi; Mohd Fathullah, Ghazli @ Ghazali; Nik Noriman, Zulkepli (EDP Sciences, 2016)

  The work reported herein is about an analysis on the quality (shrinkage) on a thick plate part using Response Surface Methodology (RSM). Previous researches showed that the most influential factor affecting the shrinkage ...

• Analysis of shrinkage on thick plate part using genetic algorithm 

  S., N. Najihah; Shayful Zamree, Abd Rahim; S., M. Nasir; Mohd Sazli, Saad; M., M. Rashidi; Mohd Fathullah, Ghazli @ Ghazali; Nik Noriman, Zulkepli (EDP Sciences, 2016)

  Injection moulding is the most widely used processes in manufacturing plastic products. Since the quality of injection improves plastic parts are mostly influenced by process conditions, the method to determine the optimum ...

• Increasing ABB FlexPicker Robot’s Degree of Freedom (DOF) using Flexible End Effector 

  M. H., Nordin; K., Selvaraju; Mohd Fathullah, Ghazli @ Ghazali (EDP Sciences, 2016)

  The commissioning of a high speed parallel robot such as the ABB Flexpicker Robot into the industrial environment provides greater flexibility in picking, packaging or palletizing tasks. However, current configuration of ...

• Application of Firefly Algorithm for Parameter Estimation of Damped Compound Pendulum 

  Mohd Sazli, Saad; Mohamad Izzat, Kamal; ‪Shayfull Zamree, Abd Rahim‬; Mohd Nasir, Mat Saad; Mohd Fathullah, Ghazli @ Ghazali (EDP Sciences, 2016)

  This paper presents an investigation into the parameter estimation of the damped compound pendulum using Firefly algorithm method. In estimating the damped compound pendulum, the system necessarily needs a good model. ...

• Parameter estimation of damped compound Pendulum using Bat Algorithm 

  Mohd Sazli, Saad; Luqman Nul Hakim, Mat Deri; Shayfull Zamree, Abd Rahim; Mohd Nasir, Mat Saad; Mohd Fathullah, Ghazli @ Ghazali (EDP Sciences, 2016)

  In this study, the parameter identification of the damped compound pendulum system is proposed using one of the most promising nature inspired algorithms which is Bat Algorithm (BA). The procedure used to achieve the ...

• A study on two plate and three plate mold of ultra thin plates in minimizing warpage issue 

  Mohd. Fathullah, Ghazli @ Ghazali; Shayfull Zamree, Abd. Rahim; Sharif, S.,; Norshah Afizi, Shuaib; Mohd. Nasir, Mat Saad (Praise Worthy Prize, 2011-11)

  The demand of ultra thin plastic parts in global industries is increasing today. Ultra thin plastic parts are widely produced using injection molding processes and it is understood that warpage issue is regularly found in ...

• Optimization of tile laying process parameters using taguchi's method 

  Norshah Afizi, Shuaib; Shayfull, Zamree Abd Rahim; Mohd. Fathullah, Ghazli @ Ghazali; Mohamad Ezral, Baharudin; Zaidi, Mohd Ripin (Praise Worthy Prize, 2011-11)

  This paper discusses the use of the Taguchi method of experimental design in optimizing process parameters of adhesion strength between tile and mortar bed. The effects of four process parameters of force, thinset mortar ...

• Warpage analysis between straight and conformal cooling channels on thin shallow shell 

  Norshah Afizi, Shuaib; Mohd Fathullah, Ghazli@Ghazali; Shayfull Zamree, Abd. Rahim; Mohd Nasir, Mat Saad; Mohd Fidzwan, Md Amin Hamzas (Trans Tech Publications, 2014)

  Warpage is a type mold defect due to non-uniform temperature variation which causes differential shrinkage rate on the moulded parts. An accurate warpage prediction is so important in helping mould designers to achieve ...

• An approach to mechanization and automation of manual construction activity 

  Mohamad Ezral, Baharudin; Shayfull Zamree, Abd Rahim; Mohd. Fathullah, Ghazli @ Ghazali; Norshah Afizi, Shuaib; Zaidi, Mohd Ripin (Praise Worthy Prize S.r.l., 2011-11)

  Construction industry is very important to the developing country like Malaysia. Many challenges and difficulties must be faced by the developers of this particular field. Warszawski et. al [1] has reported that there are ...

• Investigation on Nylon PA66 side arms using Taguchi and ANOVA analysis in reducing cost of producing urinary catheters 

  Mohd. Fathullah, Ghazli @ Ghazali; Shayfull Zamree, Abd Rahim; Norshah Afizi, Shuaib; Mohd. Nasir, Mat Saad; Muhamad Saifuldin, Abdul Manan (Praise Worthy Prize, 2011-11)

  This article discusses on a research experience and finding based on a collaboration with a medical equipment manufacturer in producing urinary catheters. The manufacturer had been spending high cost yearly to replace more ...

• Application of IDEF3 process description capture to mechanize manual tile installation 

  Mohamad Ezral, Baharudin; Mohd. Fathullah, Ghazli @ Ghazali; Norshah Afizi, Shuaib; Shayfull Zamree, Abd Rahim, Dr.; Zaidi, Mohd Ripin (Praise Worthy Prize, 2011-11)

  Integrated Definition for Function which is also known as IDEF is a well structured modeling method that corresponds to a manufacturing system. For IDEF3, it is a process description capturing method created to capture ...

• Optimal process conditions of warpage with thin-shallow features molded with pin-point gating system 

  Mohd Fathullah, Ghazli@Ghazali; Shayfull Zamree, Abd Rahim; Norshah Afizi, Shuaib; Mohd Nasir, Mat Saad; Muhamad Saifuldin, Abdul Manan (Praise Worthy Prize, 2011-11)

  Thin shallow plastic parts are widely produced using injection molding processes in producing varieties of components and applications. Warpage issue always happens in manufacturing thin shallow parts due to its uneven ...

• Potential of conformal cooling channels in rapid heat cycle molding: a review 

  Shayfull Zamree, Abd Rahim; Safian, Sharif; Azlan, Mohd Zain; Rozaimi, Mohd Saad; Mohd Fathullah, Ghazli@ Ghazali (Wiley Periodicals, Inc., 2014)

  Rapid heat cycle molding (RHCM) can eliminate the weld line, increase flow length, and improve surface quality of the molded parts. However, the cycle time is much longer as compared to the conventional injection-molding ...

• Optimization on parameter settings in determining warpage factors of a side-gated thin shallow part injection molding for PP, ABS & PC+ABS materials 

  Norshah Afizi, Shuaib; Muhamad Nasir, Murad; Mohd. Fathullah, Ghazli @ Ghazali; Shayfull Zamree, Abd Rahim; Muhammad Syahril, Bahari (Praise Worthy Prize S.r.l., 2012-05)

  The injection molding process of thin shallow part requires several concerns in order to produce a quality output. In part of determining the best parameter settings, among other considerations that need to be taken are ...

• The influence of different mold temperature on warpage in a thin shallow injection molding process 

  Norshah Afizi, Shuaib; Muhamad Nasir, Murad; Mohd. Fathullah, Ghazli @ Ghazali; Shayfull Zamree, Abd Rahim; Muhamad Saifuldin, Abdul Manan, Dr. (Praise Worthy Prize S.r.l., 2012)

  Every injection molding parameter have its own influence towards the quality of an injection-molded part. Temperature, pressure and time are main parameters that typically highlighted in controlling the warpage defect of ...

• Warpage analyses on thin plate in three-plate mold by Taguchi method and analysis of variance (ANOVA) for PC, ABS and PC/ABS 

  Shayfull Zamree, Abd Rahim; Mohd. Fathullah, Ghazli @ Ghazali; Mohd. Nasir, Mat Saad; Norshah Afizi, Shuaib; Muhamad Saifuldin, Abdul Manan, Dr. (Praise Worthy Prize S.r.l., 2012)

  Warpage is a common issue in plastic injection molding process. It can get worse for thin parts and therefore it is more challenging for product design engineers, mold designers and manufacturing engineer to cope with ...

View more