• The fabrication of heparin imprinted fiber membrane using electrospinning 

  Ahmad Shamir, Hasli (Universiti Malaysia Perlis (UniMAP), 2016-06)

  The studies of the fabrication of Heparin Imprinted Fiber membrane using Electrospinning was presented and investigated. This studies is about electrospinning method use to produce membrane from Polyvinylidene fluoride ...

• Lightweight material based on fly ash geopolymer 

  Yusra Saiyidah, Md Yusop (Universiti Malaysia Perlis (UniMAP), 2016-05)

  The utilization of fly ash in geopolymer concrete as an alternative to Ordinary Portland Cement partial replacement of cement gaining immerse importance today, mainly account of improvement in long term durability of ...

• Preparation and characterization of epoxy modified with palm oil based Polyol (POBP) with different curing systems 

  Nur Haziqah, Abdul Rahman (Universiti Malaysia Perlis (UniMAP), 2016-06)

  This research concentrates on preparation and characterization of epoxy modified with palm oil based polyol (POBP) with different curing systems. The effect of POBP is investigated with ten ratios of epoxy samples with two ...

• Silica extraction from agricultural waste as corrosion inhibitor 

  Nur Amni, Mohd Ezani (Universiti Malaysia Perlis (UniMAP), 2016-06)

  Rice husk and rice straw are found abundant as by-product of the the rice milling industry. Both of the agricultural wastes have a great potential to be used as raw material in industry. Rice husk and rice straw normally ...

• The use of solvents in epoxy/graphene conductive materials 

  Tang, Shin Yee (Universiti Malaysia Perlis (UniMAP), 2017-06)

  The influences of graphene nanofiller on physical, electrical and mechanical properties of epoxy composite were investigated. Epoxy was loaded with different content of graphene 0, 0.2, 0.4, 0.6, 0.8 and 1.0 vol% via ...

• Synthesis and characterization of Cobalt/Calcium Carbonate catalyst in the production of carbon nanotubes 

  Ong, Huey Lin (Universiti Malaysia Perlis (UniMAP), 2017-06)

  Since its discovery, carbon nanotubes (CNTs) have been widely researched owing to their large potential in nanotechnological applications. The effects of catalyst calcination behavior (temperature and duration) on the ...

• Effect of Zinc additions on Sn-0.7Cu-0.05Ni lead free solder alloy 

  Nurul Ashikin, Saleh (Universiti Malaysia Perlis (UniMAP), 2017-06)

  This project is focusing on the effect of zinc additions on Sn-0.7Cu-0.05Ni lead free solder alloy. The additional of micro-alloying have been developed by using casting technique with different percentage of zinc which ...

• Effect of Citric acid on properties of Cassava starch foam 

  Nur Fatehah, Shafari (Universiti Malaysia Perlis (UniMAP), 2017-06)

  The effects of citric acid towards the properties of cassava starch foam was studied in this thesis. The influences of crosslinking on cassava starch was described fundamentally. This include the formation of cell sizes, ...

• The Effect of Granulated Blast Furnace Slag (GBFS) Composition on Geopolymer Paste Properties 

  Nurul Nabihah, Abdul Razak (Universiti Malaysia Perlis (UniMAP), 2017)

  For the research study, I will perform the effect of Granulated Blast Furnace Slag (GBFS) composition on geopolymer paste properties. For my final year project, I will use raw materials of slag and fly ash that was provided ...

• The effect of treated and untreated Citronella filler loading on curing characteristic and mechanical properties of NR/SBR blends 

  Ooi, Wooi Keat (Universiti Malaysia Perlis (UniMAP), 2017-04)

  In this research, the effect of treated and untreated of Citronella filler loading from 10 phr until 50 phr on curing characteristic and mechanical properties of NR/SBR blends were studied. The Citronella leaves were ...

• Study on the microstructure and properties of Al-Zn alloy fabricated by sand casting process 

  Syed Mohd Fikri, Syed Sulaiman (Universiti Malaysia Perlis (UniMAP), 2017-06)

  In this research, the microstructure and properties of aluminium zinc (Al-Zn) alloy with different weight percentage have been studied. This project were carried out by sand casting process. The as-cast sample were prepared ...

• Properties of CNTs/Calcium Carbonate filled polymer composites 

  Siti Maisarah, Suhaimi (Universiti Malaysia Perlis (UniMAP), 2017-06)

  In the present work, the properties of the synthesized hybrid carbon nanotube-calcium carbonate (CNTs-CaCO3), prepared via chemical vapor deposition and a physically mixed CNTs-CaCO3 filled epoxy composites, at various ...

• Optimization of resistance spot welding process parameter on Galvanised steel by using Taguchi Method 

  Poorani, Jaraman (Universiti Malaysia Perlis (UniMAP), 2017-06)

  In this experimental study, three resistance spot welding parameters were varied on galvanized steel to determine the optimum value of parameters by using the Taguchi method of analysis. Selected parameters are welding ...

• Effect of MAPP coupling agent on the mechanical and morphological properties of the Polypropylene/Aluminum Hydroxide composites 

  Soo, Chang Ru (Universiti Malaysia Perlis (UniMAP), 2017)

  To improve the compatibility of aluminum hydroxide (Al(OH)3) and polypropylene (PP), the effect of maleic anhydride-grafted polypropylene (MAPP) on the mechanical and morphological properties of 15 wt.% Al(OH)3/PP composites ...

• Application of Ag/Zno nanoparticles as photocatalyst for self cleaning fabric 

  Siti Zulaiha, Mohmad Sahbudin (Universiti Malaysia Perlis (UniMAP), 2017-06)

  This project is to study the ability of ZnO particles as photocatalyst in self-cleaning fabric and to improve the photocatalytic activity of self-cleaning fabric by doping ZnO with Ag nanoparticles. Both ZnO and Ag/ZnO ...

• A study on corrosion behavior of Mild Steel in Granulated Blast Furnace (GBFS) fly ash geopolymer 

  Siti Farahnabilah, Muhd Amli (Universiti Malaysia Perlis (UniMAP), 2017-04)

  This research presents the corrosion behavior of mild steel embedded in geopolymer paste that produced by the reaction of fly ash and slag with an alkaline activators (NaOH molarity of 12 M, Na2SiO3/NaOH ratio of 2.5). ...

• Solid electrolyte for intermediate temperature solid Oxide fuel cell 

  Nurul Fatihah, Ahamad (Universiti Malaysia Perlis (UniMAP), 2020-06)

  Solid oxide fuel cell (SOFCs) have potential to generate high efficiency electrical energy converted from chemical energy with minimum impact to the environment. This thesis were aimed to study the structure and electrical ...

• Synthesis and characterization of lead free SnCu & SnCu/SiC composite solder 

  Nur Syahirah, Mohamad Zaini (Universiti Malaysia Perlis (UniMAP), 2017-06)

  The hazardous contain in lead solders have stimulate the current researchers to develop a lead free solders with a same or superior properties. A new approach has been done by introduce a lead free composite solder with ...

• Synthesis and characterization of biomimetic of Zinc Oxide 

  Nur Aziah, Abdul Rahim (Universiti Malaysia Perlis (UniMAP), 2017-06)

  This research explores the preparation and characterization of zinc oxide catalyst prepared by using mint and pine leaves as template respectively and investigation of its catalytic activity for the photoreduction of Fe3+ ...

• Anodizing process of Mg alloy using low potential 

  Siti Auni Shafiqah, Makhtar (Universiti Malaysia Perlis (UniMAP), 2017-04)

  This project is focusing on the effect of anodizing on the coating Mg alloys. The Mg alloy was cut with constant length and width. The AZ80 is the type of Mg alloy used. It has high strength but also have high corrosion ...

View more