Mohd Shukry Abdul Majid, Assoc. Prof. Ir. Dr.
Browse by
About Associate Professor Ir. Dr. Mohd Shukry Abdul Majid
Associate Professor Ir. Dr. Mohd Shukry Abdul Majid is currently a Associate Professor at Faculty of Mechanical Engineering & Technology, Universiti Malaysia Perlis
He was formerly from School of Electrical Systems Engineering
ORCID ID: https://orcid.org/0000-0002-7872-2623
Scopus Author ID: 26428832600
Email: Mohd Shukry Bin Abdul Majid
Research Interests
Composite materials
Biocomposites
Nanocomposites
Recent Submissions
-
The Characterization of Bario Rice Starch-nanoHA Scaffolds using SEM and Dielectric Measurement
(IOP Publishing, 2019)Bone tissue scaffold had been ventured for over the decades as a solution for bone failure and trauma. Starch is the most common natural polymer that has been used as a biomaterials and a good candidate for scaffold ... -
Hardened Glass Particle and Carbon Black using Resin for Potential Electromagnetic Shielding in Biomedical Electronic Equipments
(IOP Publishing, 2019)This study aims to investigate the electromagnetic properties of a composite of hardened glass particle and carbon using resin in determining the absorbability of the composite for electromagnetic interference (EMI). The ... -
The Optimization of the Hydroxyapatite (HA) Material Characteristics Produced from Corbiculacea (Etok) Shells
(IOP Publishing, 2019)Hydroxyapatite commonly used in medical field for tissue disease, bone disease, drug delivery and also for non-medical field purpose such as wastewater treatment. Due to excellent biocompatibility and bioactive properties, ... -
Effect of pineapple leaf (PALF), napier, and hemp fibres as filler on the scratch resistance of epoxy composites
(Elsevier, 2019)This article presents the effects of pineapple leaf (PALF), napier, and hemp fibres as filler on the scratch resistance of epoxy composites. In particular, it explores the effect of these natural fillers on the horizontal ... -
Motorbike engine faults diagnosing system using neural network
(IEEE Conference Publications, 2008-12)Monitoring systems for motorbike industry requires high and efficient degree of performance. In recent years, automatic identification and diagnosis of motorbike engine faults has become a very complex and critical task. ... -
Qualification and lifetime modelling of fibreglass pipe
(Maney Publishing, 2011-03)Procedures for qualifying fibreglass pipes are discussed here in relation to industry needs. The ultimate elastic wall stress (UEWS) test appears to provide an efficient means of rating pressure pipe, and indeed vessels, ... -
Application of frame energy based DCT moments for the damage diagnosis in steel plates using FLNN
(IEEE Conference Publications, 2012-12)This paper discusses the application of frame energy based Discrete Cosine Transformation (DCT) moment features for the detection of damages in steel plates. A simple experimental model is devised to suspend the steel ... -
Steel plate damage diagnosis using probabilistic neural network
(IEEE Conference Publications, 2013-01)This paper discusses the application of frame energy based DFT spectral band features for the detection of damages in steel plates. A simple experimental model is devised to suspend the steel plates in a free-free condition. ... -
Stress analysis of adhesive bonding of urea granulator fluidization bed
(Trans Tech Publications, 2014-06)Stress analysis of adhesive bonding of urea granulator fluidization bed was performed by using finite element method. The main objective of this project is to develop an alternative joining technique for urea granulator ... -
The interlaminar shear strength test of helical wound glass fibre reinforced epoxy laminates subjected to hydrothermal ageing
(Trans Tech Publications, 2014-06)This paper presents the experimental investigation of interlaminar shear strength (ILSS) tests of helical wound glass fibre reinforced epoxy (GRE) pipes subjected to hydrothermal ageing. Currently, the test is being used ... -
Strength of ductile adhesive butt joint bonded with dissimilar adherents: effect of surface roughness
(Trans Tech Publications, 2014-06)The purpose of this project is to study the influence of the macroscopic state of surface roughness of the dissimilar adherent on the strength of adhesive joint. In this project, several types of sandpaper were used to ... -
Electrical properties investigation of unsaturated polyester resin with carbon black as fillers
(Trans Tech Publications, 2014-06)In this paper, conducting polymer composites were prepared by adding different percentage of carbon black (2, 4, 6 and 8)% to unsaturated polyester resin. Hence, this project focuses on two types of carbon black which is ... -
Strength of three-point-bending ductile adhesive joint with dissimilar adherent
(Trans Tech Publications, 2014-06)In this study, an experimental investigation was conducted in order to determine the effect of different adhesive thickness (i.e., 0.1, 0.5, 0.7 and 1 mm) on strength of ductile adhesive joint. The study scope covers both ... -
Short-term test of ±55 filament wound GRE composite pipes under multiaxial stress ratios
(Trans Tech Publications, 2014-06)This paper discusses the the development of an automated pressure testing rig to perform a short term test; Ultimate Elastic Wall Stress (UEWS) for ±55˚ glass fibre reinforced epoxy (GRE) composite pipe under various stress ... -
Effect of nano-clay and their dispersion techniques on compressive properties of unsaturated polyester resin
(Trans Tech Publications, 2014-06)This paper aims to understand the relationship between processing parameters and compressive properties of nanoclay filled polyester resin (dispersion method and wt% of nanoclay particles). Unsaturated polyester resin with ... -
Stress and thermal analysis of CubeSat structure
(Trans Tech Publications, 2014-06)This paper presents the stress and thermal analysis on the CubeSat structure to study the survivability of the CubeSat during the launching process or operating condition at the orbit is presented. Various design of ... -
Effects of elevated temperatures on the compression strength of nanoclay filled unsaturated polyester resin
(Trans Tech Publications, 2014-06)The paper describes the effects of the montmorillonite (MMT) fillers commonly known as nanoclay, on the compression properties of unsaturated polyester resins at different weight percentage of nanoclay. Modified resin ... -
3D finite element stress analysis of butt adhesively bonded dissimilar joint: effect of bond thickness on strength
(Trans Tech Publications, 2014-06)The butt joint is the most studied type of adhesive joints in the literature. However, the joint strength prediction of joints is still a controversial issue as it involves a lot of factors that are difficult to quantify ... -
Tensile strength of untreated napier grass fibre reinforced unsaturated polyester composites
(Trans Tech Publications, 2014-06)This paper describes the experimental investigation of the tensile strength of untreated Napier grass fibre reinforced polyester composites. Napier grass fibres were extracted trough conventional water retting process and ... -
Effect of adhesive thickness on adhesively bonded T-joint
(IOP Publishing Ltd, 2013)The aim of this work is to analyze the effect of adhesive thickness on tensile strength of adhesively bonded stainless steel T-joint. Specimens were made from SUS 304 Stainless Steel plate and SUS 304 Stainless Steel ...