Browsing School of Manufacturing Engineering (FYP) by Issue Date
Now showing items 1-20 of 338
-
Process improvement towards the seeding process of Crystallization for refined sugar production in Chuping, Perlis
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008)Sugar technology is an infinity improvement technology which it always needed improvement for future growth. That have a lot of inconsistent factors or noises influence its manufacturing process and the productivity of ... -
Temperature reduction in mushroom house using the principle of waterfall
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008)The design and concept of mushroom house where can be maintain at 24°c were investigated by using the principle of heat transfer. The water was pumped from the tank to dome roof and flow through the pipe on the both side ... -
Reusability of plastic
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008)Plastic is light, easy to store and transport, comes in variety of textures and shapes and can hold almost anything. Those properties make it attractive to manufacturers and packagers, who use it for any application. A ... -
Ergonomics study and analysis of flexible manufacturing system
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-01)Nowadays, the market trend has been demanding increased diversity in product offerings, along with frequent updates to each product. This in turn is influencing manufacturing to invest in more flexible equipment for new ... -
Design and fabrication of mushroom house to maintain temperature at 26°C
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-01)Concept Generation and Pugh Chart Theories is the method to design the mushroom house. It will consider all the parameter or thing to happen while designing a part or product. It also will guide design process of concept ... -
Designing a pressure gauge / indicator for kitchen gas stove
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)A kitchen stove, cooker or cook stove is a kitchen appliance designed for the purpose of cooking food. Kitchen stoves rely on the application of direct heat for the cooking process and may also contain an oven, used for ... -
Motorized Wheelbarrow
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Wheelbarrows have been extensively used for carrying cement, refuse, tools and other materials. It is a simple device that eases the process of transporting materials. However, it requires the user’s strength to push it ... -
To study a design of two and three-plate mould for injection moulding process
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The purpose of this project to learn and practice design guideline for plastic injection moulding process in design mould. There include to understand all the factor that will affect the design product example poor design ... -
Design and implementation of a robotic model for Virtual Reality (VR) application
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, a virtual robotic environment of the Flexible Manufacturing System (FMS) laboratory at Kg Wai, UniMAP has been developed. The virtual robotic environment consists of two ABB robots and a conveyor system. ... -
Design improvement and fabrication and analysis of schoolbag for elementary school student
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)This thesis is a full report on improvement in schoolbag design for elementary school students. Nowadays, elementary school student were carrying too much weight on their back to school every days. Its will become affected ... -
Investigation new sensing SnTiO3 as thin film light sensor
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, some research has been done on Tin dioxide (SnO2) and stannium titanate perovskite (SnTiO3) thin films. It has been known that tin dioxide has various applications, especially for gas sensor, light sensor, ... -
Study of influence Plasma Arc cutting with response surface method
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The properties of plasma generated for the air plasma cutting process have been investigated in this study. The plasma arc cutting process employs a plasma torch with a very narrow bore to produce a transferred arc to the ... -
Robust setting of Ti-6Al-4V machining using WEDM (Low Energy with Electrolysis Free Circuit Off )
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Titanium alloys such as Ti-6Al-4V are increasingly used in aerospace and automotive industries, and also used as medical implant material in wide variety of applications. Wire-electro discharge machining (WEDM) is an ... -
Case study of implementation process and the impact of ISO 14000 to an organization
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Manufacturing factories in Malaysia are aware about the environmental impact from the waste that they produce. There are various systems that control the environment impact. One of the tools that have been widely use is ... -
Development of anthropometry database for Malaysian university student
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Anthropometry defined as a measurement of the human body and its biomechanical characteristic. Database defined as an organized collection of related records. The purpose of this project is to develop a Database System ... -
Using Pattern Matching technique for feature recognition of STEP file
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)This project utilizes the pattern matching technique for feature recognition of STEP file. It is proposed as an input for automatic feature recognition in the Computer Aided Design and Manufacturing (CAD/CAM) application. ... -
A study on the machining parameters optimization of WEDW machining TI-6AL-4V: effect on surface roughness, MRR and cutting speed
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The purpose of this project is to optimize the WEDM combination parameters in order to get the highest material removal rate (MRR), fastest cutting speed (CS) and finest surface roughness (SR) on material of titanium alloy ... -
Build mushroom house using a product design phase method that is product generation and evaluation
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Product Design Phase method that is Product Generation and Evaluation is one of the method to design a Mechanical parts or products. It will consider all the parameter or thing to happen while designing a part or product. ... -
Robust setting of Ti-6Al-4V machining using WEDM (High energy with EF Circuit Off)
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, some research had been done on optimization of wire electrical discharge machining (WEDM) parameters. It has been known that WEDM is a specialized thermal machining process which accurately machines parts ... -
The effect of pollution production in gas burner combustion system using Curve Vane Radial Air Swirler
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Swirling flow is a main flow produced by air swirled in gas turbine engine. Such flow is the combination of swirling and vortex breakdown. Swirling flow is widely used to stabilize the flame in combustion chamber. Its ...