Shamsul Baharin Jamaludin, Prof. Dr.: Recent submissions
Now showing items 41-60 of 87
-
Fly ash as Sand Replacement Material (SRM) in the development of composite cement: Physical and mechanical properties
(Universiti Malaysia Perlis (UniMAP), 2012-06-18)There has been vast research enhancing the usage of industrial wastes in engineering applications. This research paper reports the effect of fly ash on the physical and mechanical properties of composite cement. Fly ash ... -
Selective extraction, separation and recovery of Cu(II) in presence of Zn(II) and Ni(II) from leach liquor of waste printed circuit board using microcapsules coated with Cyanex 272
(Springer Verlag, 2012-05)The study was conducted to optimize the selective extraction and recovery of Cu(II) in the presence of Zn(II) and Ni(II) from the leach liquor of waste printed circuit boards (PCBs). The extraction experiments were carried ... -
The effects of superheating treatment on distribution of eutectic silicon particles in A357-continuous stainless steel composite
(Trans Tech Publications, 2013)In the present study, superheating treatment has been applied on A357 reinforced with 0.5 wt.% (Composite 1) and 1.0 wt.% (Composite 2) continuous stainless steel composite. In Composite 1, the microstructure displayed ... -
Mechanical properties and fracture behaviour of coconut fibre-based green composites
(Foundation for Materials Science and Engineering “Serban Solacolu”, 2012)This paper presents the influence of natural fibre content on the mechanical properties of coconut fibre based-green composites. The mixture ratio of cement:sand by weight was fixed at 1:1. Coconut fibre was used as ... -
Compressive strength and crack propagation of cement composites reinforced coconut fibre
(Medwell Journals, 2012)This study presents the compressive strength and crack propagation of cement composites reinforced coconut fibre. The development of cement composites in this research were done by substituting coconut fibre to the portion ... -
Physical properties of FG HAP-F75 fabricated by powder metallurgy
(Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)Functional graded (FG) HAP-F75 was prepared by powder metallurgy technique. Three layers of functional graded HAP-F75 was fabricated using single punch hydraulic press. The fabrication technique consists of mixing, pressing ... -
Development of coconut fiber with the addition of fly ash for cement panel application in construction
(Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)Natural fibers exist in large quantities and have been classified as waste materials. Coconut fiber is one of them and it is used as addition in fabrication of cement panel. Industrial waste materials such fly ash is ... -
Fabrication and mechanical properties of composite palm ash mixed with phenolic resins
(International Network for Scientific Information Publication (INSI), 2011-11)Brake pad is one of the important engineering components in automobile and it is fabricated by combination of various materials. Asbestos is one of the components in brake pad that is harmful to the human. In this ... -
Potential of palm oil clinker as reinforcement in aluminium matrix composites for tribological applications
(University of Malaya, 2011)This research studied the potential of palm oil clinker as reinforcement in composite based aluminium for tribological applications. Palm oil clinker particle (POCp) reinforced aluminium matrix composites at different ... -
Microstructure and microhardness properties of Fe-Cr-Al2O3 composites
(Universiti Putra Malaysia (UPM), 2010)The requirement for high performance materials of high wear and corrosion resistance lead to an increasing interest in ferrous matrix composites. Metal matrix composite of iron-chromium reinforced with alumina was fabricated ... -
Preliminary study of hap addition to Co-Cr-Mo alloy fabricated by powder metallurgy method
(SIRIM, 2010-11-22)This preliminary study of HAP addition in Co-Cr-Mo (F-75) was carried out by powder metallurgy method. The lab work comprises the mixing of Co-Cr-Mo with different HAP (hydroxyapatite) composition which varied from 0 wt. ... -
The effects of Al2O3 amount on the microstructure and properties of Fe-Cr matrix composites
(Springer, 2010-12)Iron based matrix composites reinforced with 5 to 25 wt pct of Al2O3 particles were fabricated using the powder metallurgy method. The samples were prepared by mixing at 250 rpm for 30 minutes, uniaxially pressing at 750 ... -
Effect of solution treatment on Mg galvanic anodes in CaSO4 – MG(OH)2 aqueous solution
(PETRONAS, 2009-07-20)The effect of heat treatment on the Mg anode was investigated in CaSO4-Mg(OH)2 aqueous solution. The Mg sample was solutionised at 150oC, Pure and untreated Mg anode were also studied as a reference. Eoc and Tafel corrosion ... -
Microstructural study and differential scanning alorimetry analysis at elevated temperatures of uperheated as-cast A357 alloy
(University of Malaya, 2009)The microstructure of superheated as-cast A357 alloy has been analysed to study the solidification structures of α-Al dendrites, eutectic Si particles and intermetallic compounds at different sections of the specimen. The ... -
Studies on mechanical alloying of copper-tungsten carbide composite for spot welding electrode
(Springer New York, 2009-12)This article presents a study on the properties and performance of copper-based composite reinforced with recycled tungsten carbide powder as spot welding electrode. The copper-tungsten carbide composite electrode was ... -
Recycled Aluminium Composite Pulley
(Malaysian Invention & Design Society (MINDS), 2006-05-19)Recycle Aluminium Composite Pulley was an environmental-friendly pulley from innovative recycle aluminium composite materials. This pulley was fabricated by using recycled aluminium alloy from automotive component reinforced ... -
Kayan 1: a Particle Board from Rice Husk
(Malaysian Invention and Design Society (MINDS), 2007-05-18)In this study, the particle board (kayan 1) was made from rice husk. The rice husk was blended with Urea-Formaldehyde (UF) as a binder and Ammonium Chloride (NH4C1) as a hardener before compaction using hot press. -
Enviro Composite Pulley
(Kementerian Pengajian Tinggi Malaysia (KPTM), 2005-09-30)Aluminium has been recycled since the days it was first commercially produced and today recycled aluminium accounts for one-third of global aluminium consumption worldwide. -
Husk Board: A Panel Board from Waste
(Kementerian Pengajian Tinggi Malaysia (KPTM), 2007-08-10)The invention is about a husk board, manufactured from rice husk. Rice husk is about industrial waste. The rice husks were blended with binder and a hardener before compaction by using hot press.