School of Mechatronic Engineering (FYP): Recent submissions
Now showing items 21-40 of 71
-
Condition monitoring on bearing faults of electric motor – Based on sound signal
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The condition monitoring of rotating shaft is important in terms of system maintenance and process automation, especially for the bearing which is most common component in machine or apparatuses. In this project, a general ... -
Testing and analysis of rubber base isolator using scrap tire pads
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)This paper focuses on the experimental studies on the development of low cost seismic base isolation pads using scrap automobile tire pads (STP). The mechanical properties of STP specimens are made from different tire ... -
The effect of strain rate of steel material
(Universiti Malaysia Perlis (UniMAP)School of Mechatronics Engineering, 2009-05)This project presents the effect of strain rate of steel material. Two different experiments are required in order to investigate the effect of strain rate of steel material. The first experiment is using Universal Testing ... -
Analysis of heat exchanger concentric tube by Finite Element Method
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)The objective for this project is to study the performance of heat exchanger in parallel flow and counter flow. This experiment using three different temperature of water like cold, hot and normal temperature. The governing ... -
Bearing puller design
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The focus of this project is to design a bearing puller of specific application. This project was assigned to design a bearing puller, a device for removing bearings, gears and countless other press fitted parts from ... -
Vibration analysis testing in selected vehicle cabin
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Generally, vibration generated from various sources (engine, road surface, tires, exhaust, etc.) should be considered in the design of a car body. These vibrations travel through transfer systems (drivetrain, suspension, ... -
A study maximum inhaler parameters and characteristic between normal and respiratory problem related patient
(Universiti Malaysia Perlis (UniMAP)School of Mechatronics Engineering, 2009-06)Metered Dose Inhalers (MDI) is used to prevent and relieve the symptoms and progression of certain diseases (asthma, chronic obstructive pulmonary disease, cysticfibrosis and bronchiectosis) by delivering the inhaled ... -
Development of human neck numerical model for crashworthiness assessment
(Universiti Malaysia Perlis (UniMAP)School of Mechatronics Engineering, 2009-05)Despite the recent progresses in occupant safety, protection of children is not still optimal. To offer a better understanding of child injury mechanisms, the present study proposes a dummy finite element model of newborn ... -
Design of alternative inhaler system to improve the delivery of inhaled pharmaceutical aerosol (IPA)
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The Metered Dose Inhalers (MDI) is used to prevent and relieve the symptoms and progression of certain diseases (asthma, chronic obstructive pulmonary disease, cystic fibrosis and bronchiectosis) by delivering the Inhaled ... -
Prototype development of micro hydropower house
(Universiti Malaysia Perlis (UniMAP)School of Mechatronic Engineering, 2009-04)Due to the fact that the cost of oil, gas and electricity is increasing, the engineers are urged to find alternative sources of energy. Another reason, which urges them to do so is to reduce the impacts of the environment. ... -
Analysis of thermal power cycles for use in space
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)This analysis focuses on the evaluation and analysis of thermal Brayton, Ericsson, and Rankine cycle. Under the examined conditions, the thermal efficiency, the exergy efficiency and power produced for each cycle should ... -
Numerical model of cable median barrier for crashworthiness assessment
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-03)In this project titled “Numerical Model of Cable Median Barrier for Crashworthiness Assessment”, we need to develop a numerical model of cable median barrier used at Kuala Perlis – Changlun highway. For the beginning of ... -
The design of reverted compound gear
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)This paper is about designing a reverted compound gear for automotive use. The reverted compound gear is widely use in automotive industries. This type of gear train is use in many gearboxes either in car or motorcycle. ... -
Finite element stress analysis of rubber isolators
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)Rubber isolators or rubber bearings are common to be found in engineering structures such as buildings and bridges. The isolators are used in those structures to reduce or eliminate vibration effect on the main structures. ... -
Heat treatment effects on mild steel’s mechanical properties
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)This report is determining the heat treatment effect on material mechanical properties. Mild steel is the most common form of steel as its price is relatively low while it provides material properties that are acceptable ... -
Ratcheting behaviour of aluminum under cyclic axial load
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)An experiment about uniaxial ratcheting of Aluminum was investigated and particular attention was paid to ratcheting behavior under different cyclic loading. The effect of amplitude stress and mean stress on the ratcheting ... -
Design of mechanical power transmission system of a small wind turbine for water pumping
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2009)Power transmission is one of the main components for a wind turbine. Transmission of power from a source, such as an engine or motor, through a machine to an output actuation is one of the most common machine tasks. The ... -
Designing mini model of wind turbine blades based on Horizontal Axis Wind Turbine model
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-06)Wind turbine is a rotating machine which converts the kinetic energy in wind into mechanical energy then is converts to electrical energy using electrical generator. A prototype development of Horizontal Axis Wind Turbine ... -
Characterization of the stent-grafts performance in abdominal aortic aneurysms
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Since the introduction of endovascular techniques in the early 1990s for the treatment of abdominal aortic aneurysms (AAAs), the insertion of a stent-graft (SG) into the affected artery segment has been greatly successful ... -
Performance of gas turbine cycle for combined cycle power plant
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)The gas turbine based power plant is characterized by its relatively low capital cost compared with the steam power plant. It has environmental advantages and short construction lead time. However, conventional industrial ...