Browsing School of Mechatronic Engineering (FYP) by Title
Now showing items 1-20 of 71
-
Analysis of heat exchanger concentric tube by Finite Element Method
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)The objective for this project is to study the performance of heat exchanger in parallel flow and counter flow. This experiment using three different temperature of water like cold, hot and normal temperature. The governing ... -
Analysis of thermal power cycles for use in space
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)This analysis focuses on the evaluation and analysis of thermal Brayton, Ericsson, and Rankine cycle. Under the examined conditions, the thermal efficiency, the exergy efficiency and power produced for each cycle should ... -
Autonomous path planning robot using geographical information
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2008-04)The purpose of this project is initially to present an implementation of a guidance algorithm based on the geometrical analysis for the adoption of path planning problem. A mobile robot (named toward its unique characteristic ... -
Bearing puller design
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The focus of this project is to design a bearing puller of specific application. This project was assigned to design a bearing puller, a device for removing bearings, gears and countless other press fitted parts from ... -
Characterisation of stress corrodes specimen
(Universiti Malaysia Perlis (UniMAP)School of Mechatronics Engineering, 2009-05)Characterisation of stress corrodes specimen is to investigate on the surface of failure specimens after stress corrosion specimen test and reveal the morphology for immersed and unimmersed specimen using Scanning Electron ... -
Characterization of the stent-grafts performance in abdominal aortic aneurysms
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Since the introduction of endovascular techniques in the early 1990s for the treatment of abdominal aortic aneurysms (AAAs), the insertion of a stent-graft (SG) into the affected artery segment has been greatly successful ... -
Computer simulation of a turbocharged diesel engine
(Universiti Malaysia Perlis (UniMAP)School of Mechatronic Engineering, 2009-05)This project is developing a computer program to predicting the performance o f a turbocharged diesel engine. This program was developed to calculate the mass flow rate and heat transfer of a turbocharged diesel engine. ... -
Condition monitoring in vehicle cabin using vibration signal characterization
(School of Mechatronic Engineering, 2008-03)This paper presents an approach to the condition monitoring in vehicle. A vibration test profiles is obtained in road testing of sedan sized car. The first step is to define the performance parameters under study. The ... -
Condition monitoring on bearing faults of electric motor – Based on sound signal
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The condition monitoring of rotating shaft is important in terms of system maintenance and process automation, especially for the bearing which is most common component in machine or apparatuses. In this project, a general ... -
Condition monitoring on bearing faults of electric motor – Based on vibration signal
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The condition monitoring of rotating shaft is important in terms of system maintenance and process automation, especially for the bearing which is most common component in machines or apparatuses. In this project, a ... -
A control system of fan speed controller for inhaler system to improve the delivery of inhaler pharmaceutical aerosol (IPA)
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Inhaler is one of the medical treatments that can be used to manage asthmatic symptom which is available in market. Pressurized Metered Dose Inhaler (PMDI) is suitable used for asthma patient to prevent and relieve the ... -
A controller to perform a visually tracking task in laboratory environment
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2008-04)This project is to develop the software for controller to perform a visually guided tracking task in laboratory environment. The image processing include image conversion, applying filter to remove noise, edge detection, ... -
Damage detection of PVC (poly vinyl chloride) and ABS (Acrylonitrile-Butadiene-Stryrene) pipe using non destructive vibration testing
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-03)Experimental modal analysis has grown steadily in popularity since the advent of the digital FFT spectrum analyzer in the early 1970’s. Today, impact testing (or bump testing) has become widespread as a fast and economical ... -
Data analysis of noise at different school of environment
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)This research concentrates on the investigation of different existing school environment’s noise exposures to determine the most suitable surrounding for schools and effects of noise exposure to students and teachers. Three ... -
Design a biofidelic dummy neck for crashworthiness application
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009)This project present designs a biofidelic dummy neck for crashworthiness application. The project is focused on simulate a neck response during a test in flexion or extension condition. The data such as total weight, ... -
Design a mixer for grain materials
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2008-04)Plastics extrusion is a high volume manufacturing process in which raw plastic material is melted and formed into a continuous profile. Extrusion produces items such as pipe or tubing, weather stripping, window frames, ... -
Design a mixer for grain materials
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2008-04)Polymers are materials composed of molecules of high molecular weight. These large molecules are generally called macromolecules. Because of their low density and their ability to be shaped and molded at relatively low ... -
Design and analysis of a cross flow heat exchanger
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-06)This project is about design and analysis a cross flow heat exchanger. In this project, an experiment about Diesel Engine Cycle and a Cross Flow Heat Exchanger system have been done in laboratory internal combustion ... -
Design and analysis of a humanoid head robot using CATIA
(School of Mechatronic Engineering, 2008-04)This report describes the design of humanoid robot head by using CATIA. This design is developed to show the expression of human-like emotion based on the clue done by other research group and also daily observation from ... -
Design and analysis of a shell and tube heat exchanger (one shell pass and one tube pass)
(Universiti Malaysia Perlis (UniMAP)School of Mechatronic Engineering, 2009-04)A shell and tube heat exchanger (one shell pass and one tube pass) is a heat exchange device between hot fluid and cold fluid. It is used widely in process industry for cooling, heating and heat exchange stream in ...